多孔挤压铝扁管电子芯片热沉的热性能研究

doi:10.3976/j.issn.1002-4026.2018.03.007

山东科学 ›› 2018, Vol. 31 ›› Issue (3): 39-47.doi: 10.3976/j.issn.1002-4026.2018.03.007

多孔挤压铝扁管电子芯片热沉的热性能研究

唐晟¹，赵耀华^1，2* ，刁彦华^1，2 ，全贞花^1，2

1. 北京工业大学，绿色建筑环境与节能技术北京市重点实验室，北京 100124；2. 北京未来网络科技高精尖创新中心，北京 100124

收稿日期:2018-03-01 出版日期:2018-06-20 发布日期:2018-06-20
通信作者: 赵耀华。E-mail:yhzhao@bjut.edu.cn E-mail:yhzhao@bjut.edu.cn
作者简介:唐晟（1987—），男，博士研究生，研究方向为微小通道流动与换热。
基金资助:
国家自然科学基金（51778010）

Thermal performance of a new kind of heat sink fabricated by flat aluminum multiport extruded tubes for electronic devices cooling

TANG Sheng¹,ZHAO Yao-hua^1,2*， DIAO Yan-hua^1,2,QUAN Zhen-hua^1,2

1.Beijing University of Technology，Beijing Key Laboratory of Green Built Environment and Energy Efficient Technology，Beijing 100124，China; 2.Beijing Advanced Innovation Center for Future Internet Technology，Beijing 100124，China

Received:2018-03-01 Online:2018-06-20 Published:2018-06-20

摘要/Abstract

摘要：

为了探讨多孔挤压铝扁管构成的新型微小通道热沉的换热特性，建立了三维共轭传热数值模型并通过实验验证了该模型的可靠性。模拟分析了在0.03 W的泵功消耗下，不同孔道高宽比、宽度比、孔道数目对热沉传热性能的影响，并详细计算导热热阻、对流热阻和热容热阻。讨论了不同内翅片的宽度及高度对强化传热系数 PEC的影响，提出了最佳的翅片宽度。该研究为此类型热沉的设计提供了参考依据。

关键词: 多孔挤压铝扁管, 热阻, 微小通道热沉, 数值模拟, 轴向内翅片

Abstract:

This study proposed a new kind of mini/microchannel heat sink fabricated by flat aluminum multiport extruded tubes, which was reliable for structure and simple for manufacturing process. In order to investigate the thermal characteristics of heat sinks, a threedimensional conjugated heat transfer model was developed. Meanwhile, an experiment was conducted to verify the reliability of the model, which included channel aspect ratio, channel width ratio and channel number on thermal resistance under pumping power consumption(Ω=0.03 W). In addition, the overall resistance of heat sink was divided into three parts (conduction resistance, convective resistance, and heat capacity resistance) and calculated in detail. Moreover, the effect of width and height of fins on enhancement of heat transfer factor (PEC) was discussed, and the optimized width of fins was calculated. This study provides a reference for the design of this kind of heat sink.

Key words: flat aluminum multiport extruded tubes, thermal resistance, mini/microchannel heat sink, longitudinal fins, numerical simulation

中图分类号:

TM 912.9

唐晟，赵耀华，刁彦华，全贞花. 多孔挤压铝扁管电子芯片热沉的热性能研究[J]. 山东科学, 2018, 31(3): 39-47.

TANG Sheng,ZHAO Yao-hua， DIAO Yan-hua,QUAN Zhen-hua. Thermal performance of a new kind of heat sink fabricated by flat aluminum multiport extruded tubes for electronic devices cooling[J]. SHANDONG SCIENCE, 2018, 31(3): 39-47.

参考文献

［1］PFAHL R C, McELROY J. The 2004 international electronics manufacturing initiative (iNEMI) technology roadmaps[M]// 2005 Conference on IEEE High Density Microsystem Design and Packaging and Component Failure Analysis.[S.l.] : IEEE ,2005.
［2］余建祖. 电子设备热设计及分析技术[M]. 北京：高等教育出版社, 2002.
［3］TUCKERMAN D B, PEASE R F W. Highperformance heat sinking for VLSI[J]. IEEE Electr Dev Lett, 1981，2 (5)：126129.
［4］HARMS T M, KAZMIERCZAK M J, GERNER F M. Developing convective heat transfer in deep rectangular microchannels[J]. International Journal of Heat & Fluid Flow, 1999,20(2):149157.
［5］PENG X F, PETERSON G P. The effect of thermofluid and geometrical parameters on convection of liquids through rectangular microchannels[J]. International Journal of Heat & Mass Transfer, 1995, 38(4):755758.
［6］QU W L, MUDAWAR I. Experimental and numerical study of pressure drop and heat transfer in a singlephase microchannel heat sink[J]. International Journal of Heat & Mass Transfer, 2002, 45(12):25492565.
［7］XIE X L, LIU Z J, HE Y L, et al. Numerical study of laminar heat transfer and pressure drop characteristics in a watercooled minichannel heat sink[J]. Applied Thermal Engineering, 2009, 29(1):6474.
［8］YANG X H, TAN S C, DING Y J, et al. Flow and thermal modeling and optimization of micro/minichannel heat sink[J]. Applied Thermal Engineering, 2017, 117:289296.
［9］AGOSTINI B, THONON B, BONTEMPS A. Effects of geometrical and thermophysical parameters on heat transfer measurements in smalldiameter channels[J]. Heat Transfer Engineering, 2006, 27(1):1424.
［10］DAI B M, LI M X, DANG C B, et al. Investigation on convective heat transfer characteristics of single phase liquid flow in multiport microchannel tubes[J]. International Journal of Heat & Mass Transfer, 2014, 70(3):114118.
［11］ZHANG J, DIAO Y H, ZHAO Y H, et al. An experimental study of the characteristics of fluid flow and heat transfer in the multiport microchannel flat tube[J]. Applied Thermal Engineering, 2014, 65(1/2):209218.
［12］ZHANG J, ZHAO Y H, DIAO Y H, et al. An experimental study on fluid flow and heat transfer in a multiport minichannel flat tube with microfin structures[J]. International Journal of Heat & Mass Transfer, 2015, 84:511520.
［13］WEBB R L, KIM N Y. Enhanced Heat Transfer[M]. New York，US:Taylor and Francis, 2005.

[1]	张国建, 孟浩, 熊威, 白涛, 孟现臣, 王军, 吕晓. 人工湖下连采连充煤炭开采地表移动变形预测研究[J]. 山东科学, 2023, 36(5): 33-43.
[2]	李鹏举, 钱林根, 吴强, 黄山, 陈甦. 悬挂式止水帷幕基坑降水开挖对临近高铁桥墩影响[J]. 山东科学, 2022, 35(6): 116-122.
[3]	董辉,任旭云. 基于DEM-CFD耦合方法的水合物与砂颗粒运动分析[J]. 山东科学, 2022, 35(3): 123-130.
[4]	王小雨,张聿祥. 内插中心斜杆换热管的换热性能[J]. 山东科学, 2022, 35(3): 35-42.
[5]	季璨, 刘志刚, 吕明明. 余热发电系统双S型旋流片喷嘴内部闪蒸过程数值研究[J]. 山东科学, 2021, 34(6): 77-82.
[6]	高国强, 陈国富. 多元流体油藏传热计算新模型[J]. 山东科学, 2021, 34(5): 49-57.
[7]	纪君娜. 栅栏板护面下护岸越浪数值模拟[J]. 山东科学, 2021, 34(4): 14-20.
[8]	黄庭祥, 胡成功, 姜小辉, 孙晓, 曹亮, 赵红霞. 双层皮带机防雨罩流场和粉尘浓度场分析[J]. 山东科学, 2021, 34(4): 80-86.
[9]	霍慕杰, 别海燕, 林子昕, 安维中. 转子流道倾斜式的外驱旋转压能交换器性能研究[J]. 山东科学, 2020, 33(6): 16-21.
[10]	刘进, 蒋慧略, 刘波, 杜大伟. 汽车外流场分析以及流线型改进[J]. 山东科学, 2020, 33(3): 87-92.
[11]	温永祺, 谢东繁, 王祥, 周豪. 基于车间通信的换道策略研究[J]. 山东科学, 2019, 32(4): 46-55.
[12]	孙德智，王桂青, 田长文. 基于MAGMASOFT的大型铝合金叶轮铸造工艺模拟[J]. 山东科学, 2018, 31(4): 44-49.
[13]	贾磊，季璨，江亚柯，刘志刚. 太阳花散热器的热性能分析[J]. 山东科学, 2018, 31(3): 48-54.
[14]	刘野，丁圆强，赵环宇，柴辉，赵强，徐宇柘，姜峰. 大型海洋资料浮标波浪能供电装置数值模拟研究[J]. 山东科学, 2017, 30(6): 6-14.
[15]	何燕，吴龚鹏，陈伟. 流化床反应器内活性焦流动特性的模拟研究[J]. 山东科学, 2017, 30(6): 58-64.

多孔挤压铝扁管电子芯片热沉的热性能研究

Thermal performance of a new kind of heat sink fabricated by flat aluminum multiport extruded tubes for electronic devices cooling

PDF (PC)

赞

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

Metrics

本文评价

推荐阅读 0