鼓泡流化床异质颗粒混合特性微观研究

doi:10.3976/j.issn.1002-4026.2022.04.009

山东科学 ›› 2022, Vol. 35 ›› Issue (4): 68-76.doi: 10.3976/j.issn.1002-4026.2022.04.009

鼓泡流化床异质颗粒混合特性微观研究

李化南(), 黄继凯(), 董开明

齐鲁工业大学(山东省科学院) 山东省科学院能源研究所,山东济南 250014

收稿日期:2021-08-18 出版日期:2022-08-20 发布日期:2022-07-25
通信作者: 黄继凯 E-mail:lhn9566@163.com;huangjk@sderi.cn
作者简介:李化南(1995—),男,硕士研究生,研究方向为多相流动与传热。E-mail: lhn9566@163.com
基金资助:
国家自然科学基金(52006111);国家自然科学基金(52076113);山东省科学院自然科学基金(2020QN008);山东省科学院自然科学基金(20192);山东省科学院科教产融合创新试点工程项目(2020KJC-GH04)

Microstudy on mixing characteristics of dissimilar particles in bubbling fluidized beds

LI Hua-nan(), HUANG Ji-kai(), DONG Kai-ming

Energy Research Institute, Qilu University of Technology (Shandong Academy of Sciences), Jinan 250014, China

Received:2021-08-18 Online:2022-08-20 Published:2022-07-25
Contact: HUANG Ji-kai E-mail:lhn9566@163.com;huangjk@sderi.cn

摘要/Abstract

摘要：

开发了一种基于电容探针的稠密气固两相流中异质颗粒混合特性测试新方法。研究了鼓泡流化床内异质颗粒混合过程中微观混合比的变化规律,分析了流化床一系列位置处对流与扩散机制对于混合过程的作用规律及其微观机理。结果表明:随着流化床床层高度的增加,对流机制对于颗粒混合的作用先增大后减小;壁面处微观混合比随着混合时间出现小幅波动,主要表现出扩散混合行为;不同高度处颗粒达到混合平衡所需时间无明显差异,而壁面处颗粒达到混合平衡所需时间是轴线处颗粒混合时间的2倍左右;混合平衡状态下最终微观混合指数相近。

关键词: 流化床, 异质颗粒, 颗粒混合, 气泡, 电容探针

Abstract:

A novel method for measuring the mixing characteristics of dissimilar particles in dense gas-solid two-phase flow based on a capacitance probe was developed. In the mixing process, the variation in the micromixing ratio of dissimilar particles in a bubbling fluidized bed was studied. The influence of convection and diffusion on the mixing of particles at a series of locations in the bubbling fluidized bed and its micromechanism were analyzed. Results show that with increasing bed height, the influence of convective mixing on the mixing of particles first increases and then decreases. The mixing ratio near the wall fluctuates slightly with the mixing time and mainly shows diffusion mixing behavior. No considerable difference is observed in the time required for particles to reach mixing equilibrium at different bed heights, and the time required for particles to reach mixing equilibrium near the wall is approximately twice as long as that at the axial positions. However, the final micromixing indices are similar in the mixing equilibrium state.

Key words: fluidized bed, dissimilar particles, particle mixing, bubble, capacitance probe

中图分类号:

TK175

李化南, 黄继凯, 董开明. 鼓泡流化床异质颗粒混合特性微观研究[J]. 山东科学, 2022, 35(4): 68-76.

LI Hua-nan, HUANG Ji-kai, DONG Kai-ming. Microstudy on mixing characteristics of dissimilar particles in bubbling fluidized beds[J]. Shandong Science, 2022, 35(4): 68-76.

图/表 6

图1

图2

图3

图4

图5

图6

参考文献 29

[1]	LOHA C, CHATTOPADHYAY H, CHATTERJEE P K. Assessment of drag models in simulating bubbling fluidized bed hydrodynamics[J]. Chemical Engineering Science, 2012, 75:400-407. DOI: 10.1016/j.ces.2012.03.044. doi: 10.1016/j.ces.2012.03.044
[2]	ZHU H P, ZHOU Z Y, YANG R Y, et al. Discrete particle simulation of particulate systems:a review of major applications and findings[J]. Chemical Engineering Science, 2008, 63(23):5728-5770. DOI: 10.1016/j.ces.2008.08.006. doi: 10.1016/j.ces.2008.08.006
[3]	ZHU H P, ZHOU Z Y, YANG R Y, et al. Discrete particle simulation of particulate systems:theoretical developments[J]. Chemical Engineering Science, 2007, 62(13):3378-3396. DOI: 10.1016/j.ces.2006.12.089. doi: 10.1016/j.ces.2006.12.089
[4]	邵应娟, 金保昇, 钟文琪, 等. 流化床异重非球颗粒混合特性试验研究[J]. 工程热物理学报, 2013, 34(4):672-675.
[5]	MARZOCCHELLA A, SALATINO P, DI PASTENA V, et al. Transient fluidization and segregation of binary mixtures of particles[J]. AIChE Journal, 2000, 46(11):2175-2182. DOI: 10.1002/aic.690461110. doi: 10.1002/aic.690461110
[6]	HUANG J K, DONG K M, LV M M, et al. Comprehensive study on the mixing behavior of small dissimilar particles in a fluidized bed[J]. Industrial & Engineering Chemistry Research, 2020, 59(50):21982-21993. DOI: 10.1021/acs.iecr.0c04603. doi: 10.1021/acs.iecr.0c04603
[7]	LU H L, HE Y R, GIDASPOW D, et al. Size segregation of binary mixture of solids in bubbling fluidized beds[J]. Powder Technology, 2003, 134(1/2):86-97. DOI:10.1016/S0032-5910(03)00126-8. doi: 10.1016/S0032-5910(03)00126-8
[8]	OLIVIERI G, MARZOCCHELLA A, SALATINO P. Segregation of fluidized binary mixtures of granular solids[J]. AIChE Journal, 2004, 50(12):3095-3106. DOI: 10.1002/aic.10340. doi: 10.1002/aic.10340
[9]	SAHOO A, ROY G K. Mixing characteristic of homogeneous binary mixture of regular particles in a gas-solid fluidized bed[J]. Powder Technology, 2005, 159(3):150-154. DOI: 10.1016/j.powtec.2005.08.010. doi: 10.1016/j.powtec.2005.08.010
[10]	魏飞, 陈卫, 金涌, 等. 气固并流系统中弥散颗粒混合行为的研究[J]. 化工冶金, 1996(3):229-234.
[11]	严建华, 朱建新, 马增益, 等. 图像法用于流化床颗粒混合特性的研究[J]. 高校化学工程学报, 2006, 20(5):745-751.
[12]	GORJI-KANDI S, ALAVI-AMLESHI S M, MOSTOUFI N. A solids mixing rate correlation for small scale fluidized beds[J]. Particuology, 2015, 21:55-64. DOI: 10.1016/j.partic.2014.10.003. doi: 10.1016/j.partic.2014.10.003
[13]	SHEN L H, XIAO J, NIKLASSON F, et al. Biomass mixing in a fluidized bed biomass gasifier for hydrogen production[J]. Chemical Engineering Science, 2007, 62(1/2):636-643. DOI: 10.1016/j.ces.2006.09.033. doi: 10.1016/j.ces.2006.09.033
[14]	ZHONG W Q, ZHANG Y, JIN B S. Novel method to study the particle circulation in a flat-bottom spout-fluid bed[J]. Energy & Fuels, 2010, 24(9):5131-5138. DOI: 10.1021/ef100435j. doi: 10.1021/ef100435j
[15]	ZHANG Y, ZHONG W Q, JIN B S. New method for the investigation of particle mixing dynamic in a spout-fluid bed[J]. Powder Technology, 2011, 208(3):702-712. DOI: 10.1016/j.powtec.2011.01.011. doi: 10.1016/j.powtec.2011.01.011
[16]	WIRSUM M, FETT F, IWANOWA N, et al. Particle mixing in bubbling fluidized beds of binary particle systems[J]. Powder Technology, 2001, 120(1/2):63-69. DOI:10.1016/S0032-5910(01)00348-5. doi: 10.1016/S0032-5910(01)00348-5
[17]	FOTOVAT F, CHAOUKI J, BERGTHORSON J. Distribution of large biomass particles in a sand-biomass fluidized bed:Experiments and modeling[J]. AIChE Journal, 2014, 60(3):869-880. DOI: 10.1002/aic.14337. doi: 10.1002/aic.14337
[18]	LIU D Y, CHEN X P. Quantifying lateral solids mixing in a fluidized bed by modeling the thermal tracing method[J]. AIChE Journal, 2012, 58(3):745-755. DOI: 10.1002/aic.12627. doi: 10.1002/aic.12627
[19]	SUTTON C R, CHEN J C. A local transient approach to monitoring fluidization quality in freely bubbling beds[J]. Powder Technology, 2008, 180(3):296-306. DOI: 10.1016/j.powtec.2007.02.022. doi: 10.1016/j.powtec.2007.02.022
[20]	WIESENDORF V, WERTHER J. Capacitance probes for solids volume concentration and velocity measurements in industrial fluidized bed reactors[J]. Powder Technology, 2000, 110(1/2):143-157. DOI:10.1016/S0032-5910(99)00276-4. doi: 10.1016/S0032-5910(99)00276-4
[21]	RICHTBERG M, RICHTER R, WIRTH K E. Characterization of the flow patterns in a pressurized circulating fluidized bed[J]. Powder Technology, 2005, 155(2):145-152. DOI: 10.1016/j.powtec.2005.05.034. doi: 10.1016/j.powtec.2005.05.034
[22]	HAGE B, WERTHER J, NARUKAWA K, et al. Capacitance probe measurement technique for local particle volume concentration in circulating fluidized bed combustors[J]. Journal of Chemical Engineering of Japan, 1996, 29(4):594-602. DOI: 10.1252/jcej.29.594. doi: 10.1252/jcej.29.594
[23]	KATO K, WEN C Y. Bubble assemblage model for fluidized bed catalytic reactors[J]. Chemical Engineering Science, 1969, 24(8):1351-1369. DOI:10.1016/0009-2509(69)85055-4. doi: 10.1016/0009-2509(69)85055-4
[24]	DAVIDSON J F, HARRISON D, JACKSON R. Fluidized particles:Cambridge University Press, 1963.155 pp. 35s[J]. Chemical Engineering Science, 1964, 19(9):701.DOI: 10.1016/0009-2509(64)85059-4. doi: 10.1016/0009-2509(64)85059-4
[25]	MAURER S, WAGNER E C, SCHILDHAUER T J, et al. X-ray measurements of bubble hold-up in fluidized beds with and without vertical internals[J]. International Journal of Multiphase Flow, 2015, 74:118-124. DOI: 10.1016/j.ijmultiphaseflow.2015.03.009. doi: 10.1016/j.ijmultiphaseflow.2015.03.009
[26]	SUN J Y, ZHOU Y F, REN C J, et al. CFD simulation and experiments of dynamic parameters in gas-solid fluidized bed[J]. Chemical Engineering Science, 2011, 66(21):4972-4982. DOI: 10.1016/j.ces.2011.06.035. doi: 10.1016/j.ces.2011.06.035
[27]	LU H L, HE Y R, GIDASPOW D, et al. Size segregation of binary mixture of solids in bubbling fluidized beds[J]. Powder Technology, 2003, 134(1/2):86-97. DOI:10.1016/S0032-5910(03)00126-8. doi: 10.1016/S0032-5910(03)00126-8
[28]	HERNÁNDEZ-JIMÉNEZ F, SÁNCHEZ-DELGADO S, GÓMEZ-GARCÍA A, et al. Comparison between two-fluid model simulations and particle image analysis & velocimetry (PIV) results for a two-dimensional gas-solid fluidized bed[J]. Chemical Engineering Science, 2011, 66(17):3753-3772. DOI: 10.1016/j.ces.2011.04.026. doi: 10.1016/j.ces.2011.04.026
[29]	LU Y J, HUANG J K, ZHENG P F, et al. Flow structure and bubble dynamics in supercritical water fluidized bed and gas fluidized bed:A comparative study[J]. International Journal of Multiphase Flow, 2015, 73:130-141. DOI: 10.1016/j.ijmultiphaseflow.2015.03.011. doi: 10.1016/j.ijmultiphaseflow.2015.03.011

鼓泡流化床异质颗粒混合特性微观研究

Microstudy on mixing characteristics of dissimilar particles in bubbling fluidized beds

RichHTML

PDF (PC)

赞

可视化

摘要/Abstract

引用本文

使用本文

图/表 6

参考文献 29

相关文章 5

Metrics

本文评价

推荐阅读 0

[1]	黄晓磊, 丁伟. 缓释型胶囊破胶剂的制备及性能研究[J]. 山东科学, 2023, 36(4): 97-103.
[2]	李臣豪, 华志励, 何锐, 连军帅, 郝宗睿. 海底冷泉气体渗漏模拟观测系统设计与开发[J]. 山东科学, 2023, 36(1): 10-17.
[3]	徐娟, 刘波, 华志励. 冷泉水体甲烷气体浓度反演方法研究[J]. 山东科学, 2019, 32(3): 10-15.
[4]	何燕，吴龚鹏，陈伟. 流化床反应器内活性焦流动特性的模拟研究[J]. 山东科学, 2017, 30(6): 58-64.
[5]	吕明明，刘志刚，管宁，王树众. T型微通道内气泡生成大小影响因素研究[J]. 山东科学, 2016, 29(5): 81-89.